Home / Tools / Simulators / GateView OTP simulator

GateView OTP and OTP-7070 RFID passage simulator

Mount a GateView OTP or OTP-7070 on the ceiling or beside a passage and walk a person through it with tagged items in a bag or a cart. See an estimate of how many item tags each pass reads, and compare the reader as it is, with CONNECTIX brAIn and, in the GateView OTP, with Identix SLP.

Loading the simulator…

Product page: GateView OTP-7070

What this simulator calculates

It estimates how many item-level RAIN RFID tags a GateView OTP or OTP-7070 reads on a person who walks through a passage, and on which side the pass was told (A to B or B to A). The body of the person blocks part of the signal, and you can switch it off to see how much it costs.

What you can set

  • Model: the OTP-7070 with two 85C7070, or the OTP with 90C4090 or 85DL4090 antennas.
  • Mounting overhead (2.2 to 4.0 m) or on the side of the passage (0.8 to 2.5 m), the tilt and the passage width.
  • Reader EZ700, EZ500 or EM300, with power, cable loss and RSSI filter per RF port: in the GateView OTP, Identix SLP runs on the EZ700 or EZ500.
  • The results compared: the reader as it is, with Impinj Gen2X, with CONNECTIX brAIn and with Identix SLP.
  • How the items pass: a bag at the side, a backpack, garments over the arm, a box in a cart or a garment rack; one or two people, the walking speed and the direction.

What you see

  • The tags a typical pass reads, and the read failures as a count of tags over the simulated passes.
  • The same setup with Impinj Gen2X on and off, side by side.
  • A 3D view of the pass: the lobe of each antenna, the zone where a tag is read in at least 90% of the tries, and the chance of a read per tag.
  • Notes on the setup, such as the EIRP of each antenna against the local limit you type in.
  • Stray reads: how often goods that must not be read (beside the reader, the next load, a neighbour) are read, with an alert and how to reduce them.

Questions about the simulator

Is the simulator free? Do I need to install anything?

It is free and runs in the browser, with no sign-up and nothing to install. It needs JavaScript and a browser with WebGL for the 3D view.

Does the result replace a test on site?

No. It is an estimate from a propagation model, the antenna patterns and premises from the literature. Use it to compare setups and prepare the project, then confirm with a pilot on site, with the real tags and products. Identix can help you plan that test.

Who is it for?

For system integrators, meaning any company that builds its own solution, in full or in part: software companies that use Identix readers, makers of their own portals or reading cabinets who buy only antennas or readers, and also installers and end users who are planning a project.

What is the difference between the OTP and the OTP-7070?

The OTP-7070 always carries two 85C7070 antennas (2 RF ports). The OTP takes 90C4090 antennas (circular, 2 RF ports, one per side) or 85DL4090 (dual linear, 4 RF ports, two per side).

What is a stray read and how do I reduce it?

A read of a tag that did not leave the store, such as the garments on a rack beside the exit. Turn on the rack beside the exit in the simulator to see how often the portal reads it. Keeping racks and shelves away from the passage, the RSSI filter, antennas pointed along the passage and recording only what crosses from side A to side B reduce it; the CONNECTIX brAIn and Identix SLP (on an EZ700 or EZ500) leave the still rack out.